|
SOLID WINTER COVERS | MESH WINTER COVERS | LEAF NET COVERS
SOLID WINTER COVER INSTALLATION
IN-GROUND SOLID COVER INSTALLATION
1. If you find that your cover is too small, do not stretch it across the pool in an attempt to make it fit. Your cover should fit your pool as shown in the diagram below.
2. Your cover is made to have rainwater accumulate on top of it all winter. This water will not damage your cover in any way. Do not pump off the cover during the Fall. Water on top of the cover will hold it in place and protect your cover from wind damage.
3. Your cover is sized for a maximum water drop below the deck of 18". If you normally drop your water more than 18" in the Fall, return your cover for a larger size. Refer to Diagram 1 for proper fit.
4. Do not use bricks or sharp blocks to weigh down your cover as they will cut and scuff the cover. We recommend using water tubes for cover installation.
5. If you tie your cover to a fence or other permanent structure, be sure to use a flexible bungie cord. This flexible cord will allow the cover to shift as snow and ice accumulates without pulling out the corner tabs or straps. Water tubes must still be used.
ABOVE-GROUND SOLID COVER INSTALLATION
1. Place cover over the entire pool and let it rest on the water.
2. Your cover is made to have rainwater accumulate on top of it all winter. This water will not damage your cover in any way. Do not pump off the cover during the Fall. Water on top of the cover will hold it in place and protect your cover from wind damage.
3. Your cover is sized for maximum water drop below the deck of about 12". If you drop your water more than 12", order a larger size.
4. Your cover should hug the sidewall of your pool and lay on top of the water. Stretching the cover will damage it. See image below for Correct and Incorrect installation diagrams.
5. Thread cable through the cover loops and use the ratchet to tighten it.
back to top
MESH WINTER COVER INSTALLATION
IN-GROUND MESH COVER INSTALLATION
1. If you find that your cover is too small, do not stretch it across the pool in an attempt to make it fit. Your cover should fit your pool as shown in the diagram below.
2. Your cover is made to have rainwater accumulate on top of it all winter. The water will slowly drain through the mesh cover. This water will not damage your cover in any way. Do not pump off the cover during the Fall. Water on top of the cover will hold it in place and protect your cover from wind damage.
3. Your cover is sized for a maximum water drop below the deck of 18". If you normally drop your water more than 18" in the Fall, return your cover for a larger size. Refer to Diagram 1 for proper fit.
4. Do not use bricks or sharp blocks to weigh down your cover as they will cut and scuff the cover. We recommend using water tubes for cover installation.
5. If you tie your cover to a fence or other permanent structure, be sure to use a flexible bungie cord. This flexible cord will allow the cover to shift as snow and ice accumulates without pulling out the corner tabs or straps. Water tubes must still be used.
ABOVE-GROUND MESH COVER INSTALLATION
1. Place cover over the entire pool and let it rest on the water.
2. Your cover is made to have rainwater accumulate on top of it all winter. The water will slowly drain through the mesh cover. This water will not damage your cover in any way. Do not pump off the cover during the Fall. Water on top of the cover will hold it in place and protect your cover from wind damage.
3. Your cover is sized for maximum water drop below the deck of about 12". If you drop your water more than 12", order a larger size.
4. Your cover should hug the sidewall of your pool and lay on top of the water. Stretching the cover will damage it. See image below for Correct and Incorrect installation diagrams.
5. Thread cable through the cover loops and use the ratchet to tighten it.
back to top
leaf net INSTALLATION
IN-GROUND LEAF NET INSTALLATION
1. INSTALL YOUR LEAF NET ON TOP OF YOUR WINTER COVER.
2. If you find that your leaf net is too small, do not stretch it across the pool in an attempt to make it fit. Your leaf net should fit your pool as shown in the diagram below.
3. Your leaf net is sized for a maximum water drop below the deck of 18". If you normally drop your water more than 18" in the Fall, return your leaf net for a larger size. Refer to diagram above for proper fit.
4. Do not use bricks or sharp blocks to weigh down your leaf net as they will cut and scuff the leaf net. We recommend using water tubes for leaf net installation.
5. If you tie your leaf net to a fence or other permanent structure, be sure to use a flexible bungie cord. This flexible cord will allow the leaf net to shift as snow and ice accumulates without pulling out the corner tabs or straps. Water tubes must still be used.
ABOVE-GROUND LEAF NET INSTALLATION
1. INSTALL YOUR LEAF NET ON TOP OF YOUR WINTER COVER.
2. Place leaf net over the entire pool and let it rest on the water.
3. Your leaf net is sized for maximum water drop below the deck of about 12". If you drop your water more than 12", order a larger size.
4. Your leaf net should hug the sidewall of your pool and lay on top of the water. Stretching the leaf net will damage it. See diagram below for correct installation technique.
5. Thread cable through the leaf net loops and use the ratchet to tighten it.
back to top
<PREVIOUS PAGE - 1 2 3 4 5 - NEXT PAGE> |
